Timing belts are typically only used on overhead camshaft engines. Timing belts are used to synchronize the crankshaft with the camshaft, similar to a timing chain on an overhead valve (pushrod) engine. Unlike a timing belt, a timing chain will normally last the life of the engine without needing service or replacement. Timing belts use raised teeth to mesh with sprockets to operate the valvetrain of an overhead camshaft engine.
Whenever a vehicle with an unknown service history comes into your repair facility or is recently purchased, here are some points that should be asked to help prevent costly engine damage:
Does the owner know if, or when the belt was replaced-
If the vehicle purchased is used, or the condition and mileage of the last timing belt replacement are unknown, it is recommended to inspect, replace or at least inform the owner that the vehicle is equipped with a timing belt.
Note the mileage of the vehicle. The average replacement interval for a timing belt is approximately 60,000 miles (96,000 km).
Engines, chain-or belt-driven, can be classified as either free-running or interference, depending on what would happen if the piston-to-valve timing were disrupted. A free-running engine is designed with enough clearance between the pistons and valves to allow the crankshaft to rotate (pistons still moving) while the camshaft stays in one position (several valves fully open). If this condition occurs normally, no internal engine damage will result. In an interference engine, there is not enough clearance between the pistons and valves to allow the crankshaft to turn without the camshaft being in time.
An interference engine can suffer extensive internal damage if a timing belt fails. The piston design does not allow clearance for the valve to be fully open and the piston to be at the top of its stroke. If the belt fails, the piston will collide with the valve and will bend or break the valve, damage the piston, and/or bend a connecting rod. When this type of failure occurs, the engine will need to be replaced or disassembled for further internal inspection; either choice costing many times that of replacing the timing belt.
For manufacturers recommended service interval, refer to the maintenance interval chart located in this manual.
The average replacement interval for a timing belt is approximately 60,000 miles (96,000km). If, however, the timing belt is inspected earlier or more frequently than suggested, and shows signs of wear or defects, the belt should be replaced at that time.
Never allow antifreeze, oil or solvents to come into with a timing belt. If this occurs immediately wash the solution from the timing belt. Also, never excessive bend or twist the timing belt; this can damage the belt so that its lifetime is severely shortened.
Fig. Never bend or twist a timing belt excessively, and do not allow solvents, antifreeze, gasoline, acid or oil to come into contact with the belt
Inspect both sides of the timing belt. Replace the belt with a new one if any of the following conditions exist:
Hardening of the rubber-back side is glossy without resilience and leaves no indentation when pressed with a fingernail
Cracks on the rubber backing
Cracks or peeling of the canvas backing
Cracks on rib root
Cracks on belt sides
Missing teeth or chunks of teeth
Abnormal wear of belt sides-the sides are normal if they are sharp, as if cut by a knife
If none of these conditions exist, the belt does not need replacement unless it is at the recommended interval. The belt MUST be replaced at the recommended interval.
On interference engines, it is very important to replace the timing belt at the recommended intervals, otherwise expensive engine damage will likely result if the belt fails.
Fig. Broken tooth may be due to a damaged pulley
Fig. Back surface worn or cracked from a possible overheated engine or interference with the belt cover
Fig. Side wear from improper installation
Fig. Worn teeth from excessive belt tension, camshaft or distributor not turning properly, or fluid leaking on the belt
Removal & Installation
The radio may have a coded theft protection circuit. Obtain the code before disconnecting the battery, removing the radio fuse, or removing the radio.
Timing belt maintenance is extremely important. All Hyundai models use interference-type non-freewheeling engines. Should the timing belt break in these engines, the valves in the cylinder head will come in contact with the pistons, causing major engine damage. The recommended replacement interval for timing belts is 60,000 miles.
On models with an air bag, wait at least 90 seconds from the time that the ignition switch is turned to the
position and the battery is disconnected before performing any further work.