Toyota Celica, Corolla, ECHO & MR2 1999-05

Exterior Lights 2

Print

Brake, Signal & Marker Lights



Removal & Installation
Turn Signal & Parking Lights
  1. Unscrew and remove the lamp assembly from the front of the lens housing.
  2.  



Click image to see an enlarged view

Fig. Remove the retaining screw holding the lamp into position



Click image to see an enlarged view

Fig. Extract the lamp and twist the socket assembly from the lamp



Click image to see an enlarged view

Fig. Inspect the light bulb filaments

  1. To remove a light bulb with retaining pins from its socket, grasp the bulb, then gently depress and twist it 1/8 turn counterclockwise, and pull it from the socket.
  2.  



Click image to see an enlarged view

Fig. Depress and twist this type of bulb counterclockwise, then pull the bulb straight from its socket



Click image to see an enlarged view

Fig. When inserting the new bulb, place the tabs into the socket and turn

To install:

  1. Before installing a light bulb into the socket, ensure that all electrical contact surfaces are free of corrosion or dirt.
  2.  

Before installing the light bulb, note the positions of the two retaining pins on the bulb. They will likely be at different heights on the bulb, to ensure that the bulb is installed correctly. If, when installing the bulb, it does not turn easily, do not force it. Remove the bulb and rotate it 180 degrees from its former position, then reinsert it into the bulb socket.

  1. Insert the light bulb into the socket and, while depressing the bulb, twist it 1/8 turn clockwise until the two pins on the light bulb are properly engaged in the socket.
  2.  
  3. To ensure that the replacement bulb functions properly, activate the applicable switch to illuminate the bulb which was just replaced. If the replacement light bulb does not illuminate, either it too is faulty or there is a problem in the bulb circuit or switch. Correct if necessary.
  4.  
  5. Install the socket and bulb assembly into the rear of the lens housing.
  6.  
  7. Insert the lamp assembly and secure with the retaining screw.
  8.  

Fog/Driving Lights



Removal & Installation


Click image to see an enlarged view

Fig. The fog lights are located in the front bumper on either side of the vehicle

  1. Loosen the retaining screw an pull out the beam unit.
  2.  



Click image to see an enlarged view

Fig. Remove the fog lamp retaining screw and pull the assembly from the bumper

  1. Turn the cover counterclockwise and remove it.
  2.  



Click image to see an enlarged view

Fig. Turn the socket counterclockwise to remove

  1. Disconnect the wiring.
  2.  



Click image to see an enlarged view

Fig. Carefully disengage the wiring from the back of the lamp

  1. Release the bulb retaining spring and remove the bulb.
  2.  



Click image to see an enlarged view

Fig. Removing and I stalling the fog light bulb

To install:

  1. Align the cutouts of the bulb with the protrusions of the mounting hole and insert the new bulb. Secure with the spring.
  2.  



Click image to see an enlarged view

Fig. Turn the socket of the fog lamp clockwise to lock

  1. Connect the wiring, install the cover and turn it clockwise so that the two triangles are aligned.
  2.  
  3. Plug the connector together.
  4.  
  5. Install the beam unit and secure with the screw.
  6.  
  7. Adjust the fog lights using the vertical adjusting screw located behind the lamp.
  8.  



Click image to see an enlarged view

Fig. An adjusting screw for the fog lights is located behind the lamp

Headlights



Aiming

The headlights must be properly aimed to provide the best, safest road illumination. The lights should be checked for proper aim and adjusted as necessary. Certain state and local authorities have requirements for headlight aiming; these should be checked before adjustment is made.


CAUTION
About once a year, when the headlights are replaced or any time front end work is performed on your vehicle, the headlight should be accurately aimed by a reputable repair shop using the proper equipment. Headlights not properly aimed can make it virtually impossible to see and may blind other drivers on the road, possibly causing an accident. Note that the following procedure is a temporary fix, until you can take your vehicle to a repair shop for a proper adjustment.

Headlight adjustment may be temporarily made using a wall, as described below, or on the rear of another vehicle. When adjusted, the lights should NOT glare in oncoming car or truck windshields, nor should they illuminate the passenger compartment of vehicles driving in front of you. These adjustments are rough and should always be fine-tuned by a repair shop which is equipped with headlight aiming tools. Improper adjustments may be both dangerous and illegal.

Horizontal and vertical aiming of each headlamp assembly is provided by two adjusting screws which move the housing against the tension of a coil spring. There is no adjustment for focus; this is done during headlight manufacturing.

Before removing the headlight bulb or disturbing the headlamp in any way, note the current settings in order to ease headlight adjustment upon reassembly. If the high or low beam setting of the old lamp still works, this can be done using the wall of a garage or a building:

  1. Park the vehicle on a level surface, with a filled fuel tank and with the vehicle empty of all extra cargo (unless normally carried). The vehicle should be facing a wall which is no less than 6 feet (1.8m) high and 12 feet (3.7m) wide. The front of the vehicle should be about 25 feet from the wall.
  2.  
  3. Bounce the vehicle several times.
  4.  



Click image to see an enlarged view

Fig. Headlight aiming screw locations

If aiming is to be performed outdoors, it is advisable to wait until dusk in order to properly see the headlight beams on the wall. If done in a garage, darken the area around the wall as much as possible by closing shades or hanging cloth over the windows.

  1. To adjust the headlight in the vertical alignment perform the following:
    1. Using the adjusting screw A , adjust the headlight aim to within specifications. Refer to the illustration.
    2.  
    3. Make sure the gage bubble is within the acceptable range.
    4.  
    5. If the bubble is outside the acceptable range, check that the vehicle is parked on a level spot. Readjust the headlight aim after parking the vehicle on the level spot.

      Click image to see an enlarged view

      Fig. The bubble should be in the middle when adjusting the vertical alignment



      Click image to see an enlarged view

      Fig. Note the bubble in the middle, this means the lamp is aligned correctly



      Click image to see an enlarged view

      Fig. Headlight aiming adjustment bubble and alignment markings

    6.  

  2.  
  3. To adjust the headlight in horizontal alignment perform the following:
    1. Using the adjusting screw B , adjust the headlight aim to within specifications.
    2.  
    3. Using a flat-bladed tool, unlock the adjusting nut C . Lift and turn to adjust.
    4.  
    5. Slide the nut C to align the top of the triangle mark to the zero position.
    6.  
    7. Press the indicator nut C until it locks securely.
    8.  

  4.  



Click image to see an enlarged view

Fig. Turn the adjusting screw to adjust the headlight within specifications



Click image to see an enlarged view

Fig. Use a flat bladed tool to unlock the adjusting nut C ...



Click image to see an enlarged view

Fig. ... once unlocked, nut C can be moved to achieve the correct headlight aiming mark then ...



Click image to see an enlarged view

Fig. ... press the nut until it locks



Click image to see an enlarged view

Fig. The adjusting nut "C" is used to adjust the O back to the mark

Removal & Installation


Click image to see an enlarged view

Fig. Headlamp bulb socket (1) and wiring harness (2)

  1. Open the vehicle's hood and secure it in an upright position.
  2.  
  3. Disconnect the wiring from the back of the bulb socket.
  4.  



Click image to see an enlarged view

Fig. The clasp is part of the connector attached to the socket



Click image to see an enlarged view

Fig. Unplug the connector while depressing the lock release ...

  1. Unfasten the locking ring which secures the bulb and socket assembly, then withdraw the assembly rearward.
  2.  



Click image to see an enlarged view

Fig. ... turn the bulb and remove it



Click image to see an enlarged view

Fig. Do NOT hold the lamp by the bulb, this will ruin a good bulb from the oils on your hand

  1. If necessary, gently pry the socket's retaining clip over the projection on the bulb (use care NOT to break the clip). Pull the bulb from the socket.
  2.  



Click image to see an enlarged view

Fig. Carefully pull the halogen headlight bulb from its socket. If applicable, release the retaining clip

To install:

  1. Before installing a light bulb into the socket, ensure that all electrical contact surfaces are free of corrosion or dirt.
  2.  
  3. Line up the replacement headlight bulb with the socket. Firmly push the bulb onto the socket until the spring clip latches over the bulb's projection.
  4.  



Click image to see an enlarged view

Fig. Insert the new bulb and connector into the mounting hole, then turn to secure


WARNING
Do NOT touch the glass bulb with your fingers. Oil from your fingers can severely shorten the life of the bulb. If necessary, wipe off any dirt or oil from the bulb with rubbing alcohol before completing installation.

  1. To ensure that the replacement bulb functions properly, activate the applicable switch to illuminate the bulb which was just replaced. (If this is a combination low and high beam bulb, be sure to check both intensities.) If the replacement light bulb does NOT illuminate, either it too is faulty or there is a problem in the bulb circuit or switch. Correct if necessary.
  2.  
  3. Position the headlight bulb and secure it with the locking ring.
  4.  
  5. Aim the headlights.
  6.  

 
label.common.footer.alt.autozoneLogo