Log In
Search suggestions

    My Vehicles

    1993 GMC Truck C1500 1/2 ton Sub 2WD 5.7L TBI 8cyl

    My Store

    405 N COLLEGE ST
    (479) 443-4043

    CLOSED Open at 7:30 AM

    GET A $25 GIFT CARD FOR EVERY $100 SPENT ON ONLINE SHIP-TO-HOME ORDERS.

    Use Code: GIFTME

    See Details

    Toyota Land Cruiser, Sequoia 6 2001-06

    Spindle Bearings

    Print

    Removal & Installation



    1. Before servicing the vehicle, refer to the Precautions section.
    2.  
    3. Remove or disconnect the following:

      Front wheel
       
      Grease cap, for 2WD
       
      Cotter pin and lock cap, for 4WD
       
      Locknut, by applying the brakes
       
      Anti-lock Brake System (ABS) speed sensor and wiring harness clamp from the steering knuckle
       
      Brake line clamp from the steering knuckle
       

    4.  


    NOTE
    Be careful not to damage the brake tube.



    Brake caliper and disc
     

    1. Support the steering knuckle
    2.  
    3. Remove or disconnect the following:

      4 lower ball joint-to-steering knuckle bolts
       
      Upper ball joint cotter pin and loosen the nut
       
      Upper ball joint from the steering knuckle using tool 09950-40011
       
      Steering knuckle by placing it in a soft-jawed vise
       
      Inside oil seal
       
      4 bolts and shift the dust cover towards the hub side (outside)
       
      Axle hub from the steering knuckle using tools 09710-30021 and 09950-40011
       
      Dust cover from the steering knuckle
       
      Bearing spacer and ABS speed sensor (with ABS) or spacer (without ABS)
       

    4.  


    WARNING
    Be careful not to scratch the speed sensor rotor serrations



    Outside oil seal from the steering knuckle
     
    Bearing snapring from the steering knuckle
     
    Bearing from the steering knuckle, using a shop press and tools 09950-60020 and 09950-70010
     



    Click image to see an enlarged view

    Fig. Exploded view of the front axle hub and related components-Sequoia

    To install:

    1. Install or connect the following:

      Bearing to the steering knuckle, using a shop press and tools 09527-17011 and 09950-60020
       
      Bearing snapring to the steering knuckle
       
      New outside oil seal to the steering knuckle, using tools 09223-15030 and 09527-17011
       
      Dust cover to the steering knuckle. Torque the 4 bolts to 13 ft. lbs. (18 Nm).
       
      Axle hub to the steering knuckle using a shop press and tool 09649-17010
       
      ABS speed sensor (with ABS) or spacer (without ABS)
       

    2.  


    WARNING
    Be careful not to scratch the speed sensor rotor serrations



    Bearing spacer, using a shop press and tools 09950-60010 and 09950-70010
     
    New inside oil seal, using tool 09527-17011 and a plastic hammer
     

    1. For 4WD, install or connect the following:
      1. Halfshaft into the axle hub and temporarily tighten the nut
      2.  

    2.  


    WARNING
    Be careful not to damage the oil seal or boot.

    1. Steering knuckle to the upper control arm. Tighten the nut to 77 ft. lbs. (105 Nm).
    2.  
    3. New cotter pin.
    4.  

    1. Install or connect the following:

      Lower ball joint to the steering knuckle. Torque the 4 bolts to 59 ft. lbs. (80 Nm).
       
      Strut
       
      Brake disc and caliper. Torque both caliper bolts to 90 ft. lbs. (123 Nm).
       
      Brake line clamp to the steering knuckle. Torque the bolt to 21 ft. lbs. (28 Nm).
       
      ABS speed sensor. Torque both bolts to 7.1 ft. lbs. (8.2 Nm).
       
      Halfshaft locknut. Torque the nut to 173 ft. lbs. (235 Nm), by applying the brakes.
       
      Lock cap and new cotter pin
       
      Grease cap, for 2WD
       
      Front wheel
       

    2.  
    3. Depress the brake pedal several times.
    4.  
    5. Check and/or adjust the front wheel alignment.
    6.  
    7. Check the ABS speed sensor signal.
    8.  

    1. Before servicing the vehicle, refer to the Precautions section.
    2.  
    3. Remove or disconnect the following:

      Front wheel
       
      Brake caliper
       
      Grease cap
       
      Snapring
       
      Hub drive flange
       
      Locknut
       
      Lockwasher
       
      Adjusting nut
       
      Outer bearing
       
      Wheel hub
       
      Disc brake dust shield
       
      Wheel speed sensor and harness
       
      Outer tie rod end
       
      Upper ball joint
       
      Lower ball joint
       
      Steering knuckle
       
      Oil seal, bushing and spindle bearing
       

    4.  


      Click image to see an enlarged view

      Fig. Removing the oil seal, bushing and spindle bearing-Land Cruiser


    To install:

    1. Coat the spindle bearing and bushing with lithium grease.
    2.  
    3. Fill the spindle cavity with lithium grease.
    4.  
    5. Press the spindle bearing and bushing into the spindle.
    6.  
    7. Install or connect the following:

      Oil seal
       
      Steering knuckle
       
      Upper ball joint. Tighten the nut to 81 ft. lbs. (110 Nm).
       
      Lower ball joint. Tighten the nut to 117 ft. lbs. (159 Nm).
       
      Outer tie rod end. Tighten the nut to 91 ft. lbs. (122 Nm).
       
      Wheel speed sensor and harness
       
      Disc brake dust shield. Tighten the bolts to 13 ft. lbs. (18 Nm).
       
      Wheel hub
       
      Outer bearing
       
      Adjusting nut. Adjust the wheel bearings.
       
      Lockwasher
       
      Locknut. Tighten the nut to 47 ft. lbs. (64 Nm).
       
      Hub drive flange. Tighten the nuts to 26 ft. lbs. (35 Nm).
       
      Snapring
       
      Grease cap
       
      Brake caliper
       
      Front wheel
       

    8.  

     
    AutoZone Logo