Toyota Tundra 2001-06

Door Glass & Regulator

Print

Power Windows



Removal & Installation
Motor & Regulator
  1. Before servicing the vehicle, refer to the Precautions section.
  2.  
  3. Using a screwdriver, remove the power window switch.
  4.  
  5. Disconnect the connectors.
  6.  
  7. Using a screwdriver, remove the courtesy light.
  8.  
  9. Disconnect the connector.
  10.  
  11. Using a screwdriver, remove the tweeter speaker cover.
  12.  
  13. Disconnect the connector.
  14.  
  15. Remove the 3 screws and tweeter speaker.
  16.  
  17. Remove the 2 caps and 2 screws.
  18.  
  19. Insert a screwdriver between the door trim and door panel to remove the door trim. Pull the door trim upward to remove it.
  20.  
  21. Remove the 2 screws and door assist grip from the door trim.
  22.  
  23. Remove the inner weatherstrip.
  24.  
  25. Remove the lower weatherstrip.
  26.  
  27. Remove the screw and remove the inside handle. Slide the inside handle backward to remove it.
  28.  
  29. Disconnect the 2 cables from the inside handle.
  30.  
  31. Disconnect the clamps and connector.
  32.  
  33. Remove the service hole cover.
  34.  
  35. Disconnect the connector.
  36.  
  37. Remove the 3 screws and speaker.
  38.  
  39. Disconnect the connector.
  40.  
  41. Remove the 3 screws and outside rear view mirror.
  42.  
  43. Using a molding remover, remove the door belt molding.
  44.  
  45. Remove the 2 bolts, nut and front lower frame.
  46.  
  47. Remove the bolt, nut and rear lower frame.
  48.  
  49. Open the door glass until the bolts appear in the service hole.
  50.  
  51. Remove the 2 bolts and door glass.
  52.  
  53. Disconnect the connector.
  54.  
  55. Remove the 5 bolts, nut and window regulator.
  56.  
  57. Remove the window regulator through the service hole.
  58.  
  59. Separate the window motor from the regulator.
  60.  

To install:

  1. Apply MP grease to the sliding and rotating parts of the window regulator.
  2.  
  3. Install the window regulator through the service hole.
  4.  
  5. Install the window regulator with the 5 bolts and nut. Tighten the bolts to 8.0 Nm (71 inch lbs) and the nut to 5.0 Nm (44 inch lbs).
  6.  
  7. Connect the connector.
  8.  
  9. Install the rear lower frame with the bolt and nut.
  10.  
  11. Install the front lower frame with the 2 bolts and nut.
  12.  
  13. Install the door glass with the 2 bolts and tighten to 5.0 Nm (44 inch lbs).
  14.  
  15. Install door belt molding
  16.  
  17. Install the outside rear view mirror with the 3 screws and tighten to 8.0 Nm (71 inch lbs).
  18.  
  19. Connect the connector.
  20.  
  21. Install the speaker with the 3 screws.
  22.  
  23. Connect the connector.
  24.  
  25. Install the service hole cover.
  26.  
  27. Connect the clamps and connector.
  28.  
  29. Connect the 2 cables to the inside handle.
  30.  
  31. Slide the inside handle forward to install it and install the screw.
  32.  
  33. Install the door assist grip to the door trim with the 2 screws..
  34.  
  35. Install lower weatherstrip.
  36.  
  37. Install inner weatherstrip.
  38.  
  39. Install the door trim with the 2 screws and 2 caps.
  40.  
  41. Install the tweeter speaker with the 3 screws, then connect the connector.
  42.  
  43. Install the tweeter speaker cover.
  44.  
  45. Connect the connector.
  46.  
  47. Install the courtesy light.
  48.  
  49. Connect the connectors.
  50.  
  51. Install the power window switch.
  52.  

 
label.common.footer.alt.autozoneLogo