Tucson 2006-2008

Locks & Lock Systems

Print

Power Door Locks



Diagnosis & Testing
Door Lock Motor

Specific to:

Hyundai Tucson 2006-2008

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the 6P connector from the front door lock motor.

    Click image to see an enlarged view

    Fig. Disconnect the 6P connector from the front door lock motor

  4.  
  5. Check door lock motor operation by connecting power and ground according to the table.
  6.  
  7. If a fault in the motor is diagnosed, replace the power door lock motor.
    WARNING
    To prevent damage to the actuator, apply battery voltage only momentarily.



    Click image to see an enlarged view

    Fig. Check actuator operation by connecting power and ground according to table

  8.  

Door Lock Switch

Specific to:

Hyundai Tucson 2006-2008

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the 6P connector from the front door lock motor.

    Click image to see an enlarged view

    Fig. Disconnect the 6P connector from the front door lock motor

  4.  
  5. Check for continuity between the terminals in each switch position according to the table. Replace power door lock switch if faulty.

    Click image to see an enlarged view

    Fig. Check for continuity between the terminals in each switch position according to the table

  6.  

Removal & Installation
Door Lock Motor
Front

Specific to:

Hyundai Tucson 2006-2008


WARNING
Be careful not to scratch the door trim and other parts. Wear gloves to protect your hands.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the front door trim.
  6.  
  7. Remove the glass.
  8.  
  9. Disconnect the 6P connector from the front door lock motor.

    Click image to see an enlarged view

    Fig. Disconnect the 6P connector from the front door lock motor

  10.  
  11. Disconnect the lock rod and outside handle rod.
  12.  
  13. Remove the door lock module.
  14.  

To install:

  1. Installation is the reverse of the removal procedure.
  2.  
  3. Make sure the connectors are plugged in properly and each cable is connected securely.
  4.  
  5. Make sure the door motor performs the lock and unlock functions properly.
  6.  
  7. Roll the glass up and down to ensure that it moves freely without binding.
  8.  

Rear

Specific to:

Hyundai Tucson 2006-2008


WARNING
Be careful not to scratch the door trim and other parts. Wear gloves to protect your hands.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the door trim.
  6.  
  7. Remove the glass.
  8.  
  9. Remove the rear channel.
  10.  
  11. Disconnect the 6P connector from the rear door lock motor.

    Click image to see an enlarged view

    Fig. Disconnect the 6P connector from the rear door lock motor

  12.  
  13. Disconnect the lock rod and outside handle rod.
  14.  
  15. Remove the door lock module.
  16.  

To install:

  1. Installation is the reverse of the removal procedure.
  2.  
  3. Make sure the connectors are plugged in properly and each cable is connected securely.
  4.  
  5. Make sure the door motor performs the lock and unlock functions properly.
  6.  
  7. Roll the glass up and down to ensure that it moves freely without binding.
  8.  

Door Lock Switch
  1. Before servicing the vehicle, refer to the Precautions Section.
  2.  
  3. Disconnect the negative battery cable.
  4.  
  5. Remove the front door trim.
  6.  
  7. Remove the power door lock and window main switch from the door trim panel.
  8.  
  9. Detach the connector from the switch.
  10.  
  11. Installation is the reverse of the removal.
  12.  

 
label.common.footer.alt.autozoneLogo