Vibe 2003-2005

Arming The System

Print

Zone 1



  1. Connect the front end sensor - left electrical connector from the front end sensor - left.
  2.  
  3. Connect the CPA from the front end sensor - left connector.
  4.  
  5. Connect the front end sensor - right electrical connector from the front end sensor - right.
  6.  
  7. Connect the CPA from the front end sensor - right connector.
  8.  
  9. Connect the battery negative cable.
  10.  
  11. Install the AM2 Fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  12.  
  13. The AIR BAG indicator will flash then turn OFF.
  14.  
  15. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  16.  

  1. Connect the front end sensor - left electrical connector from the front end sensor - left.
  2.  
  3. Connect the CPA from the front end sensor - left connector.
  4.  
  5. Connect the front end sensor - right electrical connector from the front end sensor - right.
  6.  
  7. Connect the CPA from the front end sensor - right connector.
  8.  
  9. Connect the battery negative cable.
  10.  
  11. Install the AM2 Fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  12.  
  13. The AIR BAG indicator will flash then turn OFF.
  14.  
  15. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  16.  

Zone 10



  1. Connect the SIS electrical connector.
  2.  
  3. Install the rear seat garnish molding.
  4.  
  5. Connect the negative battery cable.
  6.  
  7. Install the AM2 fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  8.  
  9. The AIR BAG indicator will flash then turn OFF.
  10.  
  11. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  12.  

  1. Connect the SIS electrical connector.
  2.  
  3. Install the rear seat garnish molding.
  4.  
  5. Connect the negative battery cable.
  6.  
  7. Install the AM2 fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  8.  
  9. The AIR BAG indicator will flash then turn OFF.
  10.  
  11. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  12.  

Zone 12



  1. Connect the SIS electrical connector.
  2.  
  3. Install the rear seat garnish molding.
  4.  
  5. Install the rear door sill plate.
  6.  
  7. Connect the negative battery cable.
  8.  
  9. Install the AM2 fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  10.  
  11. The AIR BAG indicator will flash then turn OFF.
  12.  
  13. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  14.  

  1. Connect the SIS electrical connector.
  2.  
  3. Install the rear seat garnish molding.
  4.  
  5. Install the rear door sill plate.
  6.  
  7. Connect the negative battery cable.
  8.  
  9. Install the AM2 fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  10.  
  11. The AIR BAG indicator will flash then turn OFF.
  12.  
  13. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  14.  

Zone 2



  1. Connect the SIS electrical connector.
  2.  
  3. Install the front seat belt retractor.
  4.  
  5. Install the center pillar lower trim panel.
  6.  
  7. Interior Trim.
  8.  
  9. Install the rear door sill plate.
  10.  
  11. Install the front door sill plate.
  12.  
  13. Connect the left roof rail module wiring harness yellow connector to the left roof rail module.
  14.  
  15. Install the center pillar upper trim panel.
  16.  
  17. Install the quarter upper trim panel.
  18.  
  19. Connect the battery negative cable.
  20.  
  21. Install the AM2 Fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  22.  
  23. The AIR BAG indicator will flash then turn OFF.
  24.  
  25. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  26.  

  1. Connect the SIS electrical connector.
  2.  
  3. Install the front seat belt retractor.
  4.  
  5. Install the center pillar lower trim panel.
  6.  
  7. Interior Trim.
  8.  
  9. Install the rear door sill plate.
  10.  
  11. Install the front door sill plate.
  12.  
  13. Connect the left roof rail module wiring harness yellow connector to the left roof rail module.
  14.  
  15. Install the center pillar upper trim panel.
  16.  
  17. Install the quarter upper trim panel.
  18.  
  19. Connect the battery negative cable.
  20.  
  21. Install the AM2 Fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  22.  
  23. The AIR BAG indicator will flash then turn OFF.
  24.  
  25. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  26.  

Zone 4



  1. Remove the key from the ignition switch.
  2.  
  3. Connect the left and right roof rail module wiring harness yellow connectors to the roof rail modules.
  4.  
  5. Install the center pillar upper trim panel.
  6.  
  7. Install the quarter upper trim panel.
  8.  
  9. Install the yellow 2-way connectors to the driver and passenger seat modules.
  10.  
  11. Connect the connectors and lock the connectors with the connector lock levers.
  12.  
  13. Install the yellow 2-way connector to the inflatable restraint I/P module pigtail. Connect the connector and lock the connector with the connector lock lever.
  14.  
  15. Install the I/P glove compartment.
  16.  
  17. Install the yellow 2-way connector for the inflatable restraint steering wheel module coil. Connect the connector and lock the connector with the connector lock lever.
  18.  
  19. Install the lower steering column trim cover.
  20.  
  21. Connect the battery negative cable.
  22.  
  23. Install the AM2 fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  24.  
  25. The AIR BAG indicator will flash then turn OFF. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  26.  

  1. Remove the key from the ignition switch.
  2.  
  3. Connect the left and right roof rail module wiring harness yellow connectors to the roof rail modules.
  4.  
  5. Install the center pillar upper trim panel.
  6.  
  7. Install the quarter upper trim panel.
  8.  
  9. Install the yellow 2-way connectors to the driver and passenger seat modules.
  10.  
  11. Connect the connectors and lock the connectors with the connector lock levers.
  12.  
  13. Install the yellow 2-way connector to the inflatable restraint I/P module pigtail. Connect the connector and lock the connector with the connector lock lever.
  14.  
  15. Install the I/P glove compartment.
  16.  
  17. Install the yellow 2-way connector for the inflatable restraint steering wheel module coil. Connect the connector and lock the connector with the connector lock lever.
  18.  
  19. Install the lower steering column trim cover.
  20.  
  21. Connect the battery negative cable.
  22.  
  23. Install the AM2 fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  24.  
  25. The AIR BAG indicator will flash then turn OFF. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  26.  

Zone 5



  1. Install the yellow 2-way connector to the inflatable restraint I/P module pigtail. Connect the connector and lock the connector with the connector lock lever.
  2.  
  3. Install the glove compartment.
  4.  
  5. Connect the battery negative cable.
  6.  
  7. Install the AM2 fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  8.  
  9. The AIR BAG indicator will flash then turn OFF.
  10.  
  11. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  12.  

  1. Install the yellow 2-way connector to the inflatable restraint I/P module pigtail. Connect the connector and lock the connector with the connector lock lever.
  2.  
  3. Install the glove compartment.
  4.  
  5. Connect the battery negative cable.
  6.  
  7. Install the AM2 fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  8.  
  9. The AIR BAG indicator will flash then turn OFF.
  10.  
  11. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  12.  

Zone 6



  1. Connect the SIS electrical connector.
  2.  
  3. Install the front seat belt retractor.
  4.  
  5. Install the center pillar lower trim panel.
  6.  
  7. Install the rear door sill plate.
  8.  
  9. Install the front door sill plate.
  10.  
  11. Connect the right roof rail module wiring harness yellow connector to the right roof rail module.
  12.  
  13. Install the center pillar upper trim panel.
  14.  
  15. Install the quarter upper trim panel.
  16.  
  17. Connect the negative battery cable.
  18.  
  19. Install the AM2 fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  20.  
  21. The AIR BAG indicator will flash then turn OFF.
  22.  
  23. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  24.  

  1. Connect the SIS electrical connector.
  2.  
  3. Install the front seat belt retractor.
  4.  
  5. Install the center pillar lower trim panel.
  6.  
  7. Install the rear door sill plate.
  8.  
  9. Install the front door sill plate.
  10.  
  11. Connect the right roof rail module wiring harness yellow connector to the right roof rail module.
  12.  
  13. Install the center pillar upper trim panel.
  14.  
  15. Install the quarter upper trim panel.
  16.  
  17. Connect the negative battery cable.
  18.  
  19. Install the AM2 fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  20.  
  21. The AIR BAG indicator will flash then turn OFF.
  22.  
  23. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  24.  

Zone 7



  1. Install the yellow 2-way connector to the DSM.
  2.  
  3. Connect the connector and lock the connector with the connector lock lever.
  4.  
  5. Connect the negative battery cable.
  6.  
  7. Install the AM2 fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  8.  
  9. The AIR BAG indicator will flash then turn OFF.
  10.  
  11. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  12.  

  1. Install the yellow 2-way connector to the DSM.
  2.  
  3. Connect the connector and lock the connector with the connector lock lever.
  4.  
  5. Connect the negative battery cable.
  6.  
  7. Install the AM2 fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  8.  
  9. The AIR BAG indicator will flash then turn OFF.
  10.  
  11. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  12.  

Zone 9



  1. Install the yellow 2-way connector to the PSM.
  2.  
  3. Connect the connector and lock the connector with the connector lock lever.
  4.  
  5. Connect the negative battery cable.
  6.  
  7. Install the AM2 fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  8.  
  9. The AIR BAG indicator will flash then turn OFF.
  10.  
  11. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  12.  

  1. Install the yellow 2-way connector to the PSM.
  2.  
  3. Connect the connector and lock the connector with the connector lock lever.
  4.  
  5. Connect the negative battery cable.
  6.  
  7. Install the AM2 fuse into the junction block.
    CAUTION
    Use caution while reaching in and turn the ignition switch to the ON position.

  8.  
  9. The AIR BAG indicator will flash then turn OFF.
  10.  
  11. Perform the Diagnostic System Check - Vehicle if the AIR BAG warning indicator does not operate as described.
  12.  

 
label.common.footer.alt.autozoneLogo