Volkswagen Cars 2000-05

2.8L V6 - Std 9

Print

Trouble Code: P1609



Crash Shut-Down Activated

Possible Causes:



Check the vehicle for damage
 
Reset the ECU
 

Trouble Code: P1611



MIL Call-Up Circuit, Transmission Control Module Short to Ground

Possible Causes:



Open/short circuit to ground in the communication wire from the transmission to the ECM.
 
The ECM has failed
 

Trouble Code: P1612



Electronic Control Module Incorrect Coding

Possible Causes:



(If ECM was replaced) ECM ID not the same as the replaced unit
 
ECM has failed
 
Voltage supply for Engine Control Module (ECM) has shorted
 

Trouble Code: P1613



MIL Call-up Circuit Open/Short to B+

Possible Causes:



Open/short circuit to ground from the MIL to the ECM.
 
The ECM has failed
 
The MIL light has failed (check bulb)
 

Trouble Code: P1624



MIL Requested Signature Active

Possible Causes:



(If ECM was replaced) ECM ID not the same as the replaced unit
 
ECM has failed
 
Voltage supply for Engine Control Module (ECM) has shorted
 

Trouble Code: P1626



Data BUS Powertrain Missing Message From Transmission Control

Possible Causes:



(If ECM was replaced) ECM ID not the same as the replaced unit
 
ECM has failed
 
Voltage supply for Engine Control Module (ECM) has shorted
 

Trouble Code: P1630



Acceleration Pedal Position Sensor 1 Signal Too Low

Possible Causes:



Ground between engine and chassis may be broken
 
Throttle position sensor may have failed
 
Accelerator Pedal Position Sensor 2 has failed
 
Throttle position sensor wiring may have shorted
 
Faulty voltage supply
 
ECM has failed
 

Trouble Code: P1631



Acceleration Pedal Position Sensor 1 Signal Too High

Possible Causes:



Ground between engine and chassis may be broken
 
Throttle position sensor may have failed
 
Accelerator Pedal Position Sensor 2 has failed
 
Throttle position sensor wiring may have shorted
 
Faulty voltage supply
 
ECM has failed
 

Trouble Code: P1633



Acceleration Pedal Position Sensor 2 Signal Too Low

Possible Causes:



Ground between engine and chassis may be broken
 
Throttle position sensor may have failed
 
Accelerator Pedal Position Sensor 2 has failed
 
Throttle position sensor wiring may have shorted
 
Faulty voltage supply
 
ECM has failed
 

Trouble Code: P1634



Acceleration Pedal Position Sensor 2 Signal Too High

Possible Causes:



Ground between engine and chassis may be broken
 
Throttle position sensor may have failed
 
Accelerator Pedal Position Sensor 2 has failed
 
Throttle position sensor wiring may have shorted
 
Faulty voltage supply
 
ECM has failed
 

Trouble Code: P1635



Data BUS Powertrain Missing Message From Central A/C Control

Possible Causes:



Check the Terminal resistance for CAN-bus
 
Data-Bus wires have short
 
Data-Bus components are malfunctioning
 
ECM has failed
 

Trouble Code: P1639



Accelerator Pedal Position Sensor 1+2 Range/Performance

Possible Causes:



Ground between engine and chassis may be broken
 
Throttle position sensor may have failed
 
Accelerator Pedal Position Sensor 2 has failed
 
Throttle position sensor wiring may have shorted
 
Faulty voltage supply
 
ECM has failed
 

Trouble Code: P1640



Internal Control Module (EEPROM) Error

Possible Causes:



Engine Control Module (ECM) has failed
 
Voltage supply for Engine Control Module (ECM) has shorted
 

Trouble Code: P1647



Please Check Coding of the ECUs in the Data Bus Powertrain

Possible Causes:



Engine Control Module (ECM) has failed
 
Voltage supply for Engine Control Module (ECM) has shorted
 

Trouble Code: P1648



Data Bus Powertrain Malfunction

Possible Causes:



Ground between engine and chassis may be broken
 
Throttle position sensor may have failed
 
Accelerator Pedal Position Sensor 2 has failed
 
Throttle position sensor wiring may have shorted
 
Faulty voltage supply
 
ECM has failed
 

Trouble Code: P1649



Data Bus Powertrain Missing Message from ABS Control Module

Possible Causes:



Ground between engine and chassis may be broken
 
Throttle position sensor may have failed
 
Accelerator Pedal Position Sensor 2 has failed
 
Throttle position sensor wiring may have shorted
 
Faulty voltage supply
 
Check the Terminal resistance for CAN-bus
 
Data-Bus wires have short
 
Data-Bus components are malfunctioning
 
ECM has failed
 

Trouble Code: P1650



Data Bus Powertrain Missing Message from Instrument Panel ECU

Possible Causes:



Ground between engine and chassis may be broken
 
Faulty voltage supply
 
ECM has failed
 

Trouble Code: P1690



Malfunction Indication Light Malfunction

Possible Causes:



Wire from ECM to MIL is shorted or grounded
 
ECM has failed
 
MIL has failed
 

Trouble Code: P1691



Malfunction Indication Light Open

Possible Causes:



Wire from ECM to MIL is shorted or grounded
 
ECM has failed
 
MIL has failed
 

Trouble Code: P1692



Malfunction Indication Light Short to Ground

Possible Causes:



Wire from ECM to MIL is shorted or grounded
 
ECM has failed
 
MIL has failed
 

Trouble Code: P1693



Malfunction Indication Light Short to B+

Possible Causes:



Wire from ECM to MIL is shorted or grounded
 
ECM has failed
 
MIL has failed
 

Trouble Code: P1778



Solenoid EV7 Electrical Malfunction

Possible Causes:



Valve body solenoid valve has a short
 
The TCM has failed
 
ECM has failed
 

Trouble Code: P1823



Pressure Control Solenoid 3 Electrical

Possible Causes:



Solenoid valves in valve body are faulty
 
Solenoid circuit is shorting to ground
 
Solenoid circuit is open
 
TCM has failed or wiring is shorting
 
Check harness connector for contact corrosion or water damage
 
Check resistance of solenoid valves may not be up to specification
 
Wires to Transmission Control Module (TCM) may have ground out or open
 
Transmission Control Module (TCM) has failed
 
ECM has failed
 

Trouble Code: P1828



Pressure Control Solenoid 4 Electrical

Possible Causes:



Solenoid valves in valve body are faulty
 
Solenoid circuit is shorting to ground
 
Solenoid circuit is open
 
TCM has failed or wiring is shorting
 
Check harness connector for contact corrosion or water damage
 
Check resistance of solenoid valves may not be up to specification
 
Wires to Transmission Control Module (TCM) may have ground out or open
 
Transmission Control Module (TCM) has failed
 
ECM has failed
 

Trouble Code: P1850



Data BUS Powertrain Missing Message from Engine Control

Possible Causes:



Check the Terminal resistance for CAN-bus
 
Data-Bus wires have short
 
Data-Bus components are malfunctioning
 
ECM has failed
 

Trouble Code: P1854



Data BUS Powertrain Hardware Defective

Possible Causes:



Check the Terminal resistance for CAN-bus
 
Data-Bus wires have short
 
Data-Bus components are malfunctioning
 
ECM has failed
 

Trouble Code: P1855



Data BUS Powertrain Software Version Control

Possible Causes:



Check the Terminal resistance for CAN-bus
 
Data-Bus wires have short
 
Data-Bus components are malfunctioning
 
ECM has failed
 

Trouble Code: P1857



Load Signal Error Message From Engine Control

Possible Causes:



Intake Manifold Runner Position Sensor is faulty
 
Intake system has leaks (false air)
 
Motor for intake flap is faulty
 
Mass Air Flow (MAF) sensor has failed
 
ECM has failed
 

Trouble Code: P1866



Data Bus Powertrain Missing Messages

Possible Causes:



Check the Terminal resistance for CAN-bus
 
Data-Bus wires have short
 
Data-Bus components are malfunctioning
 
ECM has failed
 

Trouble Code: P1912



Brake Booster Pressure Sensor Short Circuit to B+

Possible Causes:



Circuit short to ground or open
 
Brake booster pressure sensor has failed or is dirty
 
ECM has failed
 

Trouble Code: P1913



Brake Booster Pressure Sensor Short Circuit to Ground

Possible Causes:



Circuit short to ground or open
 
Brake booster pressure sensor has failed or is dirty
 
ECM has failed
 

Trouble Code: P2090



-B- Camshaft Position Control Circuit Low Bank 1

Possible Causes:



Camshaft position control wiring harness connector is damaged or open
 
Camshaft adjustment valve has failed
 
Circuit is open or grounded
 
Assembly is damaged or it has failed (an open circuit)
 
ECM power supply relay has failed
 
ECM has failed
 

Trouble Code: P2091



-B- Camshaft Position Control Circuit High Bank 1

Possible Causes:



Camshaft position control wiring harness connector is damaged or open
 
Camshaft adjustment valve has failed
 
Circuit is open or grounded
 
Assembly is damaged or it has failed (an open circuit)
 
ECM power supply relay has failed
 
ECM has failed
 

Trouble Code: P2096



Post Catalyst Fuel Trim System Too Lean (Bank 1)

Possible Causes:



Oxygen sensor (before catalytic converter) is faulty
 
Oxygen sensor (behind catalytic converter) is faulty
 
Oxygen sensor heater (before catalytic converter) is faulty
 
Oxygen sensor heater (behind catalytic converter) is faulty
 
Check circuits for shorts to each other, ground or power
 
ECM has failed
 

Trouble Code: P2097



Post Catalyst Fuel Trim System Too Rich (Bank 1)

Possible Causes:



Oxygen sensor (before catalytic converter) is faulty
 
Oxygen sensor (behind catalytic converter) is faulty
 
Oxygen sensor heater (before catalytic converter) is faulty
 
Oxygen sensor heater (behind catalytic converter) is faulty
 
Check circuits for shorts to each other, ground or power
 
ECM has failed
 

Trouble Code: P2098



Post Catalyst Fuel Trim System Too Lean (Bank 2)

Possible Causes:



Oxygen sensor (before catalytic converter) is faulty
 
Oxygen sensor (behind catalytic converter) is faulty
 
Oxygen sensor heater (before catalytic converter) is faulty
 
Oxygen sensor heater (behind catalytic converter) is faulty
 
Check circuits for shorts to each other, ground or power
 
ECM has failed
 

Trouble Code: P2099



Post Catalyst Fuel Trim System Too Rich (Bank 2)

Possible Causes:



Oxygen sensor (before catalytic converter) is faulty
 
Oxygen sensor (behind catalytic converter) is faulty
 
Oxygen sensor heater (before catalytic converter) is faulty
 
Oxygen sensor heater (behind catalytic converter) is faulty
 
Check circuits for shorts to each other, ground or power
 
ECM has failed
 

Trouble Code: P2101



Throttle Actuator Control Motor Range/Performance

Possible Causes:



TACM wiring harness connector is damaged or open
 
TACM wiring may be crossed in the wire harness assembly
 
TACM (motor) circuit is open, or TACM assembly is damaged (possible open circuit)
 
TACM or the Throttle Valve is dirty
 
Throttle Position sensor has failed
 
ECM has failed
 

Trouble Code: P2106



Throttle Actuator Control System - Forced Limited Power Conditions

Possible Causes:



TACM wiring harness connector is damaged or open
 
TACM wiring may be crossed in the wire harness assembly
 
TACM (motor) circuit is open, or TACM assembly is damaged (possible open circuit)
 
TACM or the Throttle Valve is dirty
 
Throttle Position sensor has failed
 
ECM has failed
 

Trouble Code: P2122



Accelerator Pedal Position Sensor -D- Circuit Low Input

Possible Causes:



Ground between engine and chassis may be broken
 
Throttle position sensor may have failed
 
Accelerator Pedal Position Sensor has failed
 
Throttle position sensor wiring may have shorted
 
Throttle position sensor has failed
 
Faulty voltage supply
 
ECM has failed
 

 
label.common.footer.alt.autozoneLogo