Volkswagen Cars 2000-05

Front End Alignment

Print

Adjustments



Caster & Camber
Camber

Looking from the front of the vehicle, camber is the inward or outward tilt of the top of wheels. When the tops of the wheels are tilted in, this is negative camber; if they are tilted out, it is positive. In a turn, a slight amount of negative camber helps maximize contact of the tire with the road. However, too much negative camber compromises straight-line stability, increases bump steer and torque steer.



Click image to see an enlarged view

Fig. Camber influences tire contact with the road

Looking from the front of the vehicle, camber is the inward or outward tilt of the top of wheels. When the tops of the wheels are tilted in, this is negative camber; if they are tilted out, it is positive. In a turn, a slight amount of negative camber helps maximize contact of the tire with the road. However, too much negative camber compromises straight-line stability, increases rolling resistance, bump steer and tighten steer.

Although not adjustable from the factory, adjustable front camber plates are available from aftermarket suppliers. Suspension tuning is a key element in improving the cornering ability of a vehicle, and should only be performed by a knowledgeable and experienced technician.

On All Wheel Drive (AWD) models, the rear camber is adjusted by loosening the locknut of a through bolt, and moving an eccentric washer that is keyed to the bolt.


WARNING
Only qualified technicians using proper equipment should make adjustments to a vehicle's alignment.



Click image to see an enlarged view

Fig. Camber influences tire contact with the road. As the top of the tire is moved away from the center of the vehicle, the camber becomes more positive

Caster

Looking at a vehicle from the side, caster angle describes the steering axis rather than a wheel angle. The steering knuckle is attached to a control arm or strut at the top and a control arm at the bottom. The wheel pivots around the line between these points to steer the vehicle. When the upper point is tilted back, this is described as positive caster. Having a positive caster tends to make the wheels self-centering, increasing directional stability. Excessive positive caster makes the wheels hard to steer, while an uneven caster will cause a pull to one side. Overloading the vehicle or sagging rear springs will affect caster, as will raising the rear of the vehicle. If the rear of the vehicle is lower than normal, the caster becomes more positive.



Click image to see an enlarged view

Fig. Caster affects straight-line stability. Caster wheels used on shopping carts, for example, employ positive caster

Looking at a vehicle from the side, caster angle describes the steering axis rather than a wheel angle. The steering knuckle is attached to a strut at the top and a control arm at the bottom. The wheel pivots around the line between these points to steer the vehicle. When the upper point is tilted back, this is described as positive caster. Having a positive caster tends to make the wheels self-centering, increasing directional stability. Excessive positive caster makes the wheels more difficult to steer, while an uneven caster will cause a pull to one side. Overloading the vehicle or sagging rear springs will affect caster, as will raising the rear of the vehicle. If the rear of the vehicle is lower than normal, the caster becomes more positive, conversely as the rear is raised, the camber is reduced.

If the front caster varies from side to side, the lower subframe fasteners can be loosened and the subframe moved slightly around the bolt holes for minute adjustments.


WARNING
Only qualified technicians using proper equipment should make adjustments to a vehicle's alignment.

Suspension tuning is a key element in improving the cornering ability of a vehicle, and should only be performed by a knowledgeable and experienced technician.



Click image to see an enlarged view

Fig. Caster affects straight-line stability. The rear caster wheels used on shopping carts, for example, employ positive caster

Toe Adjustment

Looking down at the wheels from above the vehicle, toe angle is the distance between the front of the wheels, relative to the distance between the back of the wheels. If the wheels are closer at the front, they are said to be toed-in or to have negative toe. A small amount of negative toe enhances directional stability and provides a smoother ride on the highway.



Click image to see an enlarged view

Fig. With toe-in, the distance between the wheels is closer at the front than at the rear

Looking down at the wheels from above the vehicle, toe angle is the distance between the front of the wheels, relative to the distance between the back of the wheels. If the wheels are closer at the front than at the rear, they are said to be toed-in or to have negative toe. A small amount of negative toe in the front end enhances directional stability and provides a smoother ride on the highway, however too much toe in will cause the front of the car to dart, or turn in quickly on a turn. A slight toe out may improve the ultimate turn-in ability of the vehicle, however too much toe out may cause the mid corner performance to be compromised and create excessive under-steer.

The rear toe should typically be set for toe in. Toe-out should only be approached by a professional suspension expert for extreme cases where extensive modifications have been performed and the use of specific components require ignoring factory specifications.

The front toe is adjusted by loosening a locknut and then rotating a threaded steering arm. On 1990-97 Passat models, the left side tie rod length is set to a specified distance and the total toe is set and adjusted with the right tie rod.

On A4 and 1998-00 Passat models, both tie rods are adjusted to center the steering wheel and to set the individual toe for each front wheel.

The rear toe on A4 and 1998-00 Passat All Wheel Drive (AWD) models is adjusted by moving an eccentric washer on one of the trailing arms where it attaches to the subframe.


WARNING
Only qualified technicians using proper equipment should make adjustments to a vehicle's alignment.



Click image to see an enlarged view

Fig. With toe-in, the distance between the wheels is closer at the front than at the rear



Click image to see an enlarged view

Fig. On All Wheel Drive models, the rear toe and camber are set by moving eccentric washers attached to the bushing bolt-A4 model shown



Click image to see an enlarged view

Fig. On 1990-97 Passat models, the left tie rod assembly is set to a predetermined length. The total toe is adjusted via the right tie rod

 
label.common.footer.alt.autozoneLogo