Yaris 2007

Air/Fuel Ratio Sensor

Print

Location



Specific to:

Toyota Yaris 2007-2010

Refer to the accompanying illustration.

Click image to see an enlarged view

Fig. AFR sensor location

Operation



Air-Fuel Ratio Sensor Heater

Specific to:

Toyota Yaris 2007-2010

In order to achieve operating temperature and enter closed loop more quickly, modern oxygen sensors have built-in heating elements.

Component Description

Specific to:

Toyota Yaris 2007-2010

The Air-Fuel Ratio (AFR) Sensor, also known as a Wideband Oxygen Sensor is a planar zirconia electronic device that measures the proportion of Hydrocarbons (HC) and oxygen (O2) content in the exhaust gas. The function of the AFR sensor is to constantly monitor the air-fuel ratio of the engine, determine if the mixture is rich or lean, and provide feedback (real-time information) to the Powertrain Control Module (PCM) so that the air-fuel ratio may be automatically adjusted.

Fuel Trim

Specific to:

Toyota Yaris 2007-2010

Fuel trim is the PCM parameter that is used to adjust the air-fuel mixture. The ideal AFR Sensor feedback value is 2.5 volts DC, which is indicated when air and fuel are at the stoichiometric ratio of 14.7:1. This value is determined by AFR sensor feedback, and provides the final data for the PCM in determining the correct air-fuel mixture.

Removal & Installation



Specific to:

Toyota Yaris 2007-2010

  1. Disconnect the negative battery cable.
  2.  
  3. Disconnect the air fuel ratio sensor connector and clamp.
  4.  
  5. Using SST 09224-00010, remove the heated oxygen sensor.
  6.  
  7. To install, reverse the removal procedure.
  8.  
  9. Check for exhaust gas leakage.

    Click image to see an enlarged view

    Fig. Removing the AFR sensor

  10.  

Testing



Specific to:

Toyota Yaris 2007-2010


NOTE
Refer to the Electrical Wiring Diagram for component and connector locations, connector views, and circuit-specific information.

Air/Fuel Ratio Sensor

Specific to:

Toyota Yaris 2007-2010

A properly operating heated Air-Fuel Ratio (AFR) sensor should display a level feedback signal of approximately 2.5 volts DC. If the feedback signal is not within the specified range, additional diagnosis is required in order to determine the proper function of the AFR sensor, or if a fault exists in any related sub-systems.

Air/Fuel Ratio Sensor Heater

Specific to:

Toyota Yaris 2007-2010

The AFR sensor heater may be tested by performing a resistance test; the sensor must be disconnected from the main engine wiring harness. If the circuit resistance is greater than 5.0 ohms, replace the HO2S. Refer to the Electrical Wiring Diagram for specific circuit information and connector views.

Click image to see an enlarged view

Fig. Normal AFR sensor reading.

Air/Fuel Ratio Sensor Strategy

Specific to:

Toyota Yaris 2007-2010

The AFR sensor operates most effectively when an operating temperature of 1,472° F (800°C) or higher is reached and maintained. When the AFR sensor reaches the specified temperature and begins sending the feedback signal, the PCM uses the information to enter closed loop mode, which is defined as the PCM having full control of the air-fuel ratio. In order to achieve operating temperature and enter closed loop more quickly, modern AFR sensors have built-in heating elements.

Connection & Wiring Diagnosis

Specific to:

Toyota Yaris 2007-2010

Refer to the Electrical Wiring Diagram for component and connector locations, connector views, and circuit-specific information.  

Many intermittent open or short circuits may be caused by wiring harness and connector movement due to vibration, engine torque, bumps and rough pavement, etc.

  1. Test the wiring harness and connectors by performing the following tests:

    Move the related connectors and wiring while monitoring the appropriate scan tool data.
     
    Move the related connectors and wiring with the component commanded ON and OFF. Using a suitable the scan tool, observe the component operation.
     
    With the engine running, move the related connectors and wiring while monitoring component operation.
     
    If harness or connector movement affects the data displayed, the component and system operation, or the engine operation, inspect and repair the harness or connections as necessary.
     

  2.  
  3. Test the connector terminal pins and/or wiring by performing the following tests:

    Inspect for incorrect mating of the connector halves, or terminals not fully seated in the connector body.
     
    Inspect for improperly formed or damaged terminals and test for incorrect terminal tension.
     
    Inspect for poor terminal to wire connections including terminals crimped over insulation. This requires removing the terminal from the connector body.
     
    Inspect for corrosion or water intrusion. Pierced or damaged insulation can allow moisture to enter the wiring. The conductor can corrode inside the insulation with little visible evidence. Look for swollen and/or brittle sections of wire in the suspect circuits.
     
    Inspect for wires that are broken inside the insulation by gently pulling on suspect sections of wiring.
     

  4.  

Related Diagnostic Trouble Codes

Specific to:

Toyota Yaris 2007-2010



Click image to see an enlarged view

Fig. Related Diagnostic Trouble Codes

 
label.common.footer.alt.autozoneLogo