Yaris 2007

Locks & Lock Systems

Print

Door Locks



Power Door Locks
Diagnosis & Testing


Click image to see an enlarged view

Fig. Power door lock diagnosis and testing-Hatchback-Center console switch



Click image to see an enlarged view

Fig. Power door lock diagnosis and testing-Hatchback-Door switch



Click image to see an enlarged view

Fig. Power door lock diagnosis and testing-Sedan-Door switch

Removal & Installation
Motor
Hatchback

Specific to:

Toyota Yaris 2007-2009


NOTE
This procedure is for the front and rear doors.

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the front and/or rear door trim.
  4.  
  5. Remove the window regulator assembly.
  6.  
  7. Remove front door outside handle cover:
    1. Remove the hole plug.
    2.  
    3. Using Torx® socket wrench T30, loosen the screw and remove the cover with the door lock key cylinder installed.
    4.  

  8.  
  9. Remove front/rear door lock assembly:
    1. Using Torx® socket wrench T30, loosen the 3 screws.
    2.  
    3. Move the front door lock downward, remove the outside handle frame link and remove the front door lock.
    4.  
    5. For the front door, disengage the 5 claws and open the cover.
    6.  
    7. For the rear door, disengage the 7 claws and open the 2 covers.
    8.  
    9. Disconnect the front/rear door lock remote control cable and the front/rear door inside locking cable.
    10.  
    11. Remove the door lock wire harness seal.

      Click image to see an enlarged view

      Fig. View of the front door lock assembly-hatchback



      Click image to see an enlarged view

      Fig. View of the rear door lock assembly-hatchback

    12.  

  10.  

To install:


NOTE
If reusing a door lock that has been removed, replace the packing in the connecting part with new. Make sure that no grease and dirt adheres to the packing surface in the connecting part.

  1. Apply MP grease to the sliding and rotating areas of the front door lock.
  2.  
  3. Connect the front door lock remote control cable and the front door inside locking cable.
  4.  
  5. Engage the 5 or 7 claws and close the cover(s).
  6.  
  7. Insert the door lock open rod into the front door lock, then set it to the door panel.
    NOTE
    Make sure that the outside handle link is securely engaged with the door lock.

  8.  
  9. Apply adhesive to the threads of the screws. Adhesive: Part No. 08833-00070, THREE BOND 1324 or the equivalent.
  10.  
  11. Using Torx® socket wrench T30, install the door lock with the 3 screws. Tighten to 44 inch lbs. (5 Nm).
  12.  
  13. To install, reverse the remaining removal procedure.
  14.  

Sedan

Specific to:

Toyota Yaris 2007-2009


NOTE
This procedure is for the front and rear doors.

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the door trim.
  4.  
  5. Remove the window regulator assembly.
  6.  
  7. Remove door outside handle cover:
    1. Remove the hole plug.
    2.  
    3. Using Torx® socket wrench T30, loosen the screw and remove the cover with the door lock key cylinder installed.
    4.  

  8.  
  9. Remove front door lock:
    1. Using Torx® socket wrench T30, loosen the 3 screws.
      NOTE
      Do not drop or damage the front door lock when removing the screws.

    2.  
    3. Move the door lock downward, remove the outside handle frame link and remove the door lock.
    4.  
    5. Open the cover(s).
    6.  
    7. Disconnect the door lock remote control cable and the door inside locking cable.
    8.  
    9. Remove the door lock wire harness seal.

      Click image to see an enlarged view

      Fig. View of the front door lock assembly-Sedan



      Click image to see an enlarged view

      Fig. View of the rear door lock assembly-Sedan

    10.  

  10.  

Switch
Hatchback

Specific to:

Toyota Yaris 2007-2009

  1. Disconnect the negative battery cable.
  2.  
  3. Disengage the 8 claws and remove the console box rear cover.
  4.  
  5. Disengage the 2 claws and remove the door control switch.
  6.  
  7. To install, reverse the removal procedure.

    Click image to see an enlarged view

    Fig. View of center console switch assembly

  8.  

Specific to:

Toyota Yaris 2007-2009

  1. Disconnect the negative battery cable.
  2.  
  3. Remove the door trim.
  4.  
  5. Remove the 3 screws and the power window regulator master switch.
  6.  
  7. To install, reverse the removal procedure.

    Click image to see an enlarged view

    Fig. Remove the 3 screws and the power window regulator master switch



    Click image to see an enlarged view

    Fig. View of door switch assembly-Hatchback

  8.  

Sedan
  1. Disconnect the negative battery cable.
  2.  
  3. Remove front armrest base upper panel.
  4.  
  5. Remove the 3 screws and the power window regulator master switch.
  6.  
  7. Remove door control switch:
    1. For Front passenger side with power window: Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the door control switch.
    2.  
    3. Without Power window: Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the door control switch.
    4.  

  8.  
  9. To install, reverse the removal procedure.

    Click image to see an enlarged view

    Fig. Remove the 3 screws and the power window regulator master switch



    Click image to see an enlarged view

    Fig. View of door switch assembly-Sedan

  10.  

 
label.common.footer.alt.autozoneLogo