tC 2007

Exterior Lighting

Print

Headlights



Removal & Installation
  1. Remove the front fender liner LH.
    1. Remove the 3 screws.
    2.  
    3. Partially remove the fender liner.
      NOTE
      It is not necessary to fully remove the fender liner. Partially remove it so that the bumper cover can be removed later.

    4.  

  2.  
  3. Remove the front fender liner RH.
    1. Use the same procedures described for the LH side.
    2.  

  4.  
  5. Remove the front bumper cover.

    Click image to see an enlarged view

    Fig. Remove the front bumper cover.

    1. Remove the 3 screws and 2 bolts.
    2.  
    3. Using a clip remover, remove the clip labeled A, 2 clips labeled B, and 2 radiator protectors.
    4.  
    5. Apply protective tape under the front fender.

      Click image to see an enlarged view

      Fig. Apply protective tape under the front fender.

    6.  
    7. Using a screwdriver, detach the 6 claws labeled A and 2 claws labeled B, and remove the bumper cover.
      NOTE
      Tape the screwdriver tip before use.

    8.  

  6.  
  7. Remove the headlight assembly.
    1. Remove the bolt and 2 screws.
    2.  
    3. Disengage the claw.
    4.  
    5. Disconnect the connectors.
    6.  
    7. Disengage the clamp and remove the headlight assembly.
    8.  

  8.  
  9. Installation is the reverse of the removal procedure.
  10.  

Tail Lights



Removal & Installation
Clear Lens Type

Specific to:

Scion tC 2007-2008


NOTE
Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side.

  1. Remove the rear bumper cover.

    Click image to see an enlarged view

    Fig. Remove the rear bumper cover.

    1. Remove the 4 screws.
    2.  
    3. Using a clip remover, remove the 4 clips.
    4.  
    5. Put protective tape under the quarter panel.

      Click image to see an enlarged view

      Fig. Put protective tape under the quarter panel.

    6.  
    7. Using a screwdriver, detach the 14 claws and remove the bumper cover.
      NOTE
      The illustration only shows the LH side of the vehicle. The remaining claws are on the RH side. Tape the screwdriver tip before use.

    8.  

  2.  
  3. Remove the rear combination light service cover.
    1. Disengage the claw.
    2.  
    3. Disengage the 2 guides and remove the rear combination light service cover.
    4.  

  4.  
  5. Remove the rear combination light assembly.
    1. Disconnect the connector and disengage the clamp.
    2.  
    3. Remove the 3 nuts.
    4.  
    5. Disengage the guide and pin, and remove the rear combination light assembly.
    6.  

  6.  
  7. Installation is the reverse of the removal procedure.
  8.  

Red Lens Type

Specific to:

Scion tC 2007-2008


NOTE
Use the same procedures for the RH side and LH side. The procedures listed below are for the LH side.

  1. Remove the rear bumper cover.

    Click image to see an enlarged view

    Fig. Remove the rear bumper cover.

    1. Remove the 4 screws.
    2.  
    3. Using a clip remover, remove the 4 clips.
    4.  
    5. Put protective tape under the quarter panel.

      Click image to see an enlarged view

      Fig. Put protective tape under the quarter panel.

    6.  
    7. Using a screwdriver, detach the 14 claws and remove the bumper cover.
      NOTE
      The illustration only shows the LH side of the vehicle. The remaining claws are on the RH side. Tape the screwdriver tip before use.

    8.  

  2.  
  3. Remove the rear floor service hole cover.
    1. Detach the claw and remove the rear floor service hole cover.
    2.  

  4.  
  5. Remove the rear combination light assembly LH.
    1. Disconnect the connector.
    2.  
    3. Remove the 3 nuts.
    4.  
    5. Remove the pin, and then remove the rear combination light.
    6.  

  6.  
  7. Installation is the reverse of the removal procedure.
  8.  

 
label.common.footer.alt.autozoneLogo