Log In
Search suggestions

    My Vehicles

    Add a Vehicle

    Find a Store

    Select Store

    GET A $25 GIFT CARD FOR EVERY $100 SPENT ON ONLINE SHIP-TO-HOME ORDERS.

    Use Code: GIFTME

    See Details

    Honda - Accord Prelude 1996 2000

    Oil Pressure Sender

    Print

    TESTING





    Click image to see an enlarged view

    Fig. Location of the oil pressure switch/sender

    The low oil pressure warning lamp will illuminate anytime the ignition switch is turned to the ON position without the engine running. When the engine is running, the light also illuminates if the engine oil pressure drops below a safe oil pressure level. To test the system, perform the following:

    If the oil pressure light does not work, perform the following:

    1. Turn the ignition switch to the ON position.
    2.  
    3. If the lamp does not light, check for a broken or disconnected wire around the engine and oil pressure sending unit switch.
    4.  
    5. If the wire at the connector checks out OK, pull the connector loose from the switch and, with a jumper wire, ground the connector to the engine.
    6.  
    7. With the ignition switch turned to the ON position, check the warning lamp. If the lamp lights, make sure the oil pressure switch is properly grounded in the cylinder block, and if so replace the oil pressure switch. If the lamp still fails to light, check for a burned out lamp or disconnected socket in the instrument cluster.
    8.  

    To diagnose an oil pressure light that stays on, perform the following:

    1. Check the engine oil level and top off as necessary. If the engine was 2 or more quarts low on oil, test start the engine after topping off the oil level and recheck the oil pressure light operation. If the light stays on, stop the engine immediately and go to the next step.
    2.  
    3. Disconnect the wire at the sending unit, then turn the ignition switch to the ON position. If the light remains on, check the wire from the sending unit to the gauge for being shorted to ground and repair as necessary. If the light goes out, turn the ignition switch OFF and go to the next step.
    4.  
    5. Replace the oil pressure sending switch with a known good switch.
    6.  
    7. Start the engine and check the oil pressure light operation. If the light stays on with the engine running, stop the engine immediately to avoid severe engine damage until the cause of the problem can be determined.
    8.  


    WARNING
    If the oil pressure light remains on while the engine is started, stop the engine immediately. Do not operate the engine until the cause of the problem can be determined. Operating an engine with low oil pressure will cause severe internal damage.

    Possible causes for an oil pressure light to stay on are:



    Pinched or grounded sensor wire
     
    Defective oil pressure sending unit
     
    Restricted or severely leaking oil filter
     
    Excessive internal engine bearing clearance.
     
    Insufficient or severely contaminated engine oil
     
    Blocked oil pump pickup screen or severely worn oil pump
     

    REMOVAL & INSTALLATION



    1. Locate the oil pressure sending unit on the engine.
    2.  
    3. Note the anti-theft code and radio presets for the radio.
    4.  
    5. Disconnect the negative battery cable.
    6.  
    7. Disconnect the sending unit electrical harness.
    8.  
    9. Using a pressure switch socket, deep-well socket or wrench, loosen and remove the sending unit from the engine.
    10.  

    To install:

    1. Apply a liquid thread sealant to the sending unit and install the sending unit in the engine and tighten securely.
    2.  
    3. Attach the electrical connector to the sending unit.
    4.  
    5. Check the engine oil level and top off as necessary.
    6.  
    7. Connect the negative battery cable.
    8.  
    9. Enter the anti-theft code and radio presets for the radio.
    10.  
    11. Start the engine, allow it to reach operating temperature and check for leaks.
    12.  
    13. Check for proper sending unit operation.
    14.  

     
    AutoZone Logo