GM Cadillac Deville_Fleetwood_ELD_Seville 1990-1998

Reading Codes

Print

OBD-I Systems





Click image to see an enlarged view

Fig. Diagnostic trouble codes-4.5L engine



Click image to see an enlarged view

Fig. Diagnostic trouble codes-4.9L engine



Click image to see an enlarged view

Fig. Diagnostic trouble codes-4.6L engine

Listings of the trouble codes for the various engine control systems covered in this guide are located in this section. Remember that a code only points to the faulty circuit NOT necessarily to a faulty component. Loose, damaged or corroded connections may contribute to a fault code on a circuit when the sensor or component is operating properly. Be sure that the components are faulty before replacing them, especially the expensive ones.

The Assembly Line Diagnostic Link (ALDL) connector or Data Link Connector (DLC) may be located under the dash and sometimes covered with a plastic cover labeled DIAGNOSTIC CONNECTOR.

  1. On all 1990-95 models the diagnostic trouble codes can be read by grounding test terminal B . The terminal is most easily grounded by connecting it to terminal A (internal ECM ground). This is the terminal to the right of terminal B on the top row of the ALDL connector.
  2.  
  3. Once the terminals have been connected, the ignition switch must be moved to the ON position with the engine not running.
  4.  
  5. The Service Engine Soon or Check Engine light should be flashing. If it isn't, turn the ignition OFF and remove the jumper wire. Turn the ignition ON and confirm that light is now on. If it is not, replace the bulb and try again. If the bulb still will not light, or if it does not flash with the test terminal grounded, the system should be diagnosed by an experienced driveability technician. If the light is OK, proceed as follows.
  6.  
  7. The code(s) stored in memory may be read through counting the flashes of the dashboard warning lamp. The dash warning lamp should begin to flash Code 12. The code will display as one flash, a pause and two flashes. Code 12 is not a fault code. It is used as a system acknowledgment or handshake code; its presence indicates that the PCM can communicate as requested. Code 12 is used to begin every diagnostic sequence. Some vehicles also use Code 12 after all diagnostic codes have been sent.
  8.  
  9. After Code 12 has been transmitted 3 times, the fault codes, if any, will each be transmitted 3 times. The codes are stored and transmitted in numeric order from lowest to highest.
  10.  


NOTE
The order of codes in the memory does not indicate the order of occurrence.

  1. If there are no codes stored, but a driveability or emissions problem is evident, the system should be diagnosed by an experienced driveability technician.
  2.  
  3. If one or more codes are stored, record them. Refer to the applicable Diagnostic Code chart in this section.
  4.  
  5. Switch the ignition OFF when finished with code retrieval or scan tool readings.
  6.  


NOTE
After making repairs, clear the trouble codes and operate the vehicle to see if it will reset, indicating further problems.

OBD-II Systems





Click image to see an enlarged view

Fig. The OBD-II connector is located under the driver's side of the instrument panel



Click image to see an enlarged view

Fig. A Tech 1®, or equivalent scan tool must be used to retrieve codes from 1996-00 models with the 16-pin DLC connector



Click image to see an enlarged view

Fig. If retrieving codes using a scan tool such as GM's TECH-1®, make sure to follow all of the manufacturer's directions carefully

All 1996-00 models, an OBD-II compliant scan tool must be used to retrieve the trouble codes. Follow the scan tool manufacturer's instructions on how to connect the scan tool to the vehicle and how to retrieve the codes.



Click image to see an enlarged view

Fig. OBD II trouble codes (1 of 5)



Click image to see an enlarged view

Fig. OBD II trouble codes (2 of 5)



Click image to see an enlarged view

Fig. OBD II trouble codes (3 of 5)



Click image to see an enlarged view

Fig. OBD II trouble codes (4of 5)



Click image to see an enlarged view

Fig. OBD II trouble codes (5 of 5)

 
AutoZone Logo