Log In
Search suggestions

    My Vehicles

    2004 Chevrolet Truck Silverado 2500 2WD 6.0L SFI 8cyl

    My Store

    1720 S RIDGEWOOD A
    (386) 427-1210

    OPEN 'til 9:00 PM today

    GET A $25 GIFT CARD FOR EVERY $100 SPENT ON ONLINE SHIP-TO-HOME ORDERS.

    Use Code: GIFTME

    See Details

    Toyota Celica, Corolla, ECHO & MR2 1999-05

    Idle Air Control Valve

    Print

    1. Check that the IAC valve is half open.
    2.  
    3. Connect the IAC valve connector to the IAC valve.
    4.  
    5. Disconnect the ECT sensor connector from the ECT sensor.
    6.  
    7. Turn the ignition switch ON.
    8.  
    9. Check that the IAC valve moves.
    10.  
    11. Repeat connecting and disconnecting of IAC valve connector several times and check the operation of the valve.
    12.  
    13. If operation is not as specified, replace the IAC valve.
    14.  
    15. Turn the ignition switch OFF.
    16.  
    17. Connect the ECT sensor connector to the ECT sensor.

      Click image to see an enlarged view

      Fig. Idle Air Control Valve

    18.  

    1. Check that the IAC valve is half open.
    2.  
    3. Connect the IAC valve connector to the IAC valve.
    4.  
    5. Disconnect the ECT sensor connector from the ECT sensor.
    6.  
    7. Turn the ignition switch ON.
    8.  
    9. Check that the IAC valve moves.
    10.  
    11. Repeat connecting and disconnecting of IAC valve connector several times and check the operation of the valve.
    12.  
    13. If operation is not as specified, replace the IAC valve.
    14.  
    15. Turn the ignition switch OFF.
    16.  
    17. Connect the ECT sensor connector to the ECT sensor.

      Click image to see an enlarged view

      Fig. Idle Air Control Valve

    18.  

    Operation



    The ECM is programmed with specific engine speed values to respond to different engine conditions (coolant temperature, air conditioner on/off, etc.). Sensors transmit signals to the ECM which controls the flow of air through the bypass of the throttle valve and adjusts the idle speed to the specified value. Some vehicles use an Idle Speed Control (ISC) valve while others use an Air Valve or Idle Air Control (IAC) valve to control throttle body by-pass air flow.

    Removal & Installation



    1. Disconnect the negative battery cable. Wait at least 90 seconds to work on the vehicle once the cable is disconnected to hinder air bag deployment.
    2.  
    3. Drain the engine coolant.
    4.  
    5. Remove the air cleaner cap and disconnect the control cables.
    6.  
    7. Remove the throttle body.
    8.  
    9. Remove the four retaining screws, IAC valve and gasket.
    10.  



    Click image to see an enlarged view

    Fig. Remove the four screws retaining the IAC valve to the throttle body



    Click image to see an enlarged view

    Fig. Separate the IAC and remove the gasket

    To install:

    1. Position a new gasket on the throttle body. Attach the IAC valve and secure.
    2.  



    Click image to see an enlarged view

    Fig. Always place a new gasket on the IAC before installation

    1. Attach the throttle body to the engine.
    2.  
    3. Attach the control cables, install the air cleaner cap.
    4.  
    5. Fill the cooling system.
    6.  
    7. Start the engine, top off the cooling system and check operation.
    8.  

    Testing



    1ZZ-FE VIN R
    1. Check that the IAC valve is half open.
    2.  
    3. Connect the IAC valve connector to the IAC valve.
    4.  
    5. Disconnect the ECT sensor connector from the ECT sensor.
    6.  
    7. Turn the ignition switch ON.
    8.  
    9. Check that the IAC valve moves.
    10.  
    11. Repeat connecting and disconnecting of IAC valve connector several times and check the operation of the valve.
    12.  
    13. If operation is not as specified, replace the IAC valve.
    14.  
    15. Turn the ignition switch OFF.
    16.  
    17. Connect the ECT sensor connector to the ECT sensor.

      Click image to see an enlarged view

      Fig. Idle Air Control Valve

    18.  

    2ZZ-FE VIN Y
    1. Check that the IAC valve is half open.
    2.  
    3. Connect the IAC valve connector to the IAC valve.
    4.  
    5. Disconnect the ECT sensor connector from the ECT sensor.
    6.  
    7. Turn the ignition switch ON.
    8.  
    9. Check that the IAC valve moves.
    10.  
    11. Repeat connecting and disconnecting of IAC valve connector several times and check the operation of the valve.
    12.  
    13. If operation is not as specified, replace the IAC valve.
    14.  
    15. Turn the ignition switch OFF.
    16.  
    17. Connect the ECT sensor connector to the ECT sensor.

      Click image to see an enlarged view

      Fig. Idle Air Control Valve

    18.  

    5S-FE VIN G
    1. Connect the positive (+) lead from the battery to terminal +B and negative (-) lead to terminal RSC, and check that the valve is closed.
    2.  
    3. Connect the positive (+) lead from the battery to terminal +B and negative (-) lead to terminal RSO, and check that the valve is open.
    4.  
    5. If operation is not as specified, replace the IAC valve.

      Click image to see an enlarged view

      Fig. IAC valve testing

    6.  

    7A-FE Engine
    1. Using a jumper wire, connect terminals TE1 and E1 of the DLC1.
    2.  



    Click image to see an enlarged view

    Fig. Exploded view showing IAC valve and related components

    1. After the engine rpm is kept at 900-1300 for about five seconds, check that the rpm returns to idle.
    2.  
    3. If the rpm operation is not as specified, check the IAC valve, wiring and engine ECM.
    4.  
    5. Remove the jumper wire form the DLC1.

      Click image to see an enlarged view

      Fig. Raise the idle speed between 900 and 1300 rpm for five seconds

    6.  

    1. Disconnect the IAC valve wiring.
    2.  



    Click image to see an enlarged view

    Fig. Remove the harness from the IAC valve to test the terminals

    1. Using an ohmmeter, measure the resistance between terminals +B and the other terminals ( RSC and RSO ).
    2.  



    Click image to see an enlarged view

    Fig. Use an ohmmeter to check the IAC valve resistance between terminals-7A-FE engine

    1. Resistance should be between:

      1994-95 models-19.3-22.3 ohms
       
      1996-17.0-24.5 ohms
       

    2.  

    1. If the resistance is not within specifications, replace the IAC valve.
    2.  
    3. To check the operation of the IAC valve, the engine should be at normal operating temperature and the transmission in Neutral.
      1. Connect the positive lead of the battery to terminal B+ and the negative lead to terminal RSC , then check that the valve is closed.
      2.  
      3. Connect the positive lead from the battery to terminal B+ and the negative lead to terminal RSO , then check that the valve is open.

        Click image to see an enlarged view

        Fig. Testing the IAC valve using battery voltage to see if the valve is closed-7A-FE engine



        Click image to see an enlarged view

        Fig. Testing the IAC valve using battery voltage to see if the valve is open-7A-FE engine

      4.  

    4.  
    5. If operation is not as specified, replace the IAC valve.
    6.  

     
    AutoZone Logo