Log In
Search suggestions

    My Vehicles

    2001 Ford Truck Expedition 4WD 5.4L EFI 8cyl

    My Store

    405 N COLLEGE ST
    (479) 443-4043

    OPEN 'til 9:00 PM today

    GET A $25 GIFT CARD FOR EVERY $100 SPENT ON ONLINE SHIP-TO-HOME ORDERS.

    Use Code: GIFTME

    See Details

    Envoy, Rainer, Trailblazer 2006-2007

    Spark Plugs

    Print

    Inspection & Gapping



    Check the plugs for deposits and wear. If they are not going to be replaced, clean the plugs thoroughly. Remember that any kind of deposit will decrease the efficiency of the plug. Plugs can be cleaned on a spark plug cleaning machine, which can sometimes be found in service stations, or you can do an acceptable job of cleaning with a stiff brush. If the plugs are cleaned, the electrodes must be filed flat. Use an ignition points file, not an emery board or the like, which will leave deposits. The electrodes must be filed perfectly flat with sharp edges; rounded edges reduce the spark plug voltage by as much as 50%.

    Check spark plug gap before installation. The ground electrode (the L-shaped one connected to the body of the plug) must be parallel to the center electrode and the specified size wire gauge (please refer to the Tune-Up Specifications chart for details) must pass between the electrodes with a slight drag.


    NOTE
    NEVER adjust the gap on a used platinum type spark plug.

    Always check the gap on new plugs as they are not always set correctly at the factory. Do not use a flat feeler gauge when measuring the gap on a used plug, because the reading may be inaccurate. A round-wire type gapping tool is the best way to check the gap. The correct gauge should pass through the electrode gap with a slight drag. If you're in doubt, try one size smaller and one larger. The smaller gauge should go through easily, while the larger one shouldn't go through at all. Wire gapping tools usually have a bending tool attached. Use that to adjust the side electrode until the proper distance is obtained. Absolutely never attempt to bend the center electrode. Also, be careful not to bend the side electrode too far or too often as it may weaken and break off within the engine, requiring removal of the cylinder head to retrieve it.

    Click image to see an enlarged view

    Fig. Inspect the spark plug to determine engine running conditions



    Click image to see an enlarged view

    Fig. A variety of tools and gauges are needed for spark plug service



    Click image to see an enlarged view

    Fig. Checking the spark plug gap with a feeler gauge



    Click image to see an enlarged view

    Fig. Adjusting the spark plug gap



    Click image to see an enlarged view

    Fig. If the standard plug is in good condition, the electrode may be filed flat-WARNING: do not file platinum plugs



    Click image to see an enlarged view

    Fig. The spark plug gap specification is sometimes given on a underhood label located on the upper radiator shroud

    Removal & Installation



    When you're removing spark plugs, work on one at a time. Don't start by removing the plug wires all at once, because, unless you number them, they may become mixed up. Take a minute before you begin and number the wires with tape.

    1. Disconnect the negative battery cable, and if the vehicle has been run recently, allow the engine to thoroughly cool.
    2.  
    3. On the 4.2L engine, remove the ignition coils. On the 5.3L and 6.0L engines, carefully twist the spark plug wire boot to loosen it, then remove the boot from the plug. Be sure to pull on the boot and not on the wire, otherwise the connector located inside the boot may become separated.
    4.  
    5. On the 5.3L and 6.0L engines, remove the washer solvent container to gain access to the No. 2 spark plug.
    6.  
    7. Using compressed air, blow any water or debris from the spark plug well to assure that no harmful contaminants are allowed to enter the combustion chamber when the spark plug is removed. If compressed air is not available, use a rag or a brush to clean the area.
      NOTE
      Remove the spark plugs when the engine is cold, if possible, to prevent damage to the threads. If removal of the plugs is difficult, apply a few drops of penetrating oil or silicone spray to the area around the base of the plug, and allow it a few minutes to work.

    8.  
    9. Using a spark plug socket that is equipped with a rubber insert to properly hold the plug, turn the spark plug counterclockwise to loosen and remove the spark plug from the bore.
      WARNING
      Be sure not to use a flexible extension on the socket. Use of a flexible extension may allow a shear force to be applied to the plug. A shear force could break the plug off in the cylinder head, leading to costly and frustrating repairs.



      Click image to see an enlarged view

      Fig. Remove the spark plug wire by pulling on the boot



      Click image to see an enlarged view

      Fig. Using a spark plug socket with a rubber insert, turn the plug counterclockwise to loosen it



      Click image to see an enlarged view

      Fig. Remove the spark plug from the bore

    10.  

    To install:

    1. Inspect the spark plug boot for tears or damage. If a damaged boot is found, the spark plug wire must be replaced.
    2.  
    3. Using a wire feeler gauge, check and adjust the spark plug gap. When using a gauge, the proper size should pass between the electrodes with a slight drag. The next larger size should not be able to pass while the next smaller size should pass freely.
    4.  
    5. Carefully thread the plug into the bore by hand. If resistance is felt before the plug is almost completely threaded, back the plug out and begin threading again. In small, hard to reach areas, an old spark plug wire and boot could be used as a threading tool. The boot will hold the plug while you twist the end of the wire and the wire is supple enough to twist before it would allow the plug to crossthread.
      WARNING
      Do not use the spark plug socket to thread the plugs. Always carefully thread the plug by hand or using an old plug wire to prevent the possibility of crossthreading and damaging the cylinder head bore.

    6.  
    7. Carefully tighten the spark plug. If the plug you are installing is equipped with a crush washer, seat the plug, then tighten about 1 / 4 turn to crush the washer. If you are installing a tapered seat plug, tighten the plug to specifications provided by the vehicle or plug manufacturer.
    8.  
    9. On the 5.3L and 6.0L engines, install the washer solvent container to gain access to the No. 2 spark plug.
    10.  
    11. On the 4.2L engine, install the ignition coils. On the 5.3L and 6.0L engines, apply a small amount of silicone dielectric compound to the end of the spark plug lead or inside the spark plug boot to prevent sticking, then install the boot to the spark plug and push until it clicks into place. The click may be felt or heard, then gently pull back on the boot to assure proper contact.
    12.  

     
    AutoZone Logo