Jeep Grand Cherokee ABS Sensor

Buy Online. Pick Up In-Store.

What are you working on today?

Get an exact fit for your Jeep Grand Cherokee
Do the complete brake job Save 15% on a set of any Duralast® brake pads and any two Duralast Brake Rotors.

1-21 of 21 Results

1-21 of 21 Results

      About


      Jeep Grand Cherokee ABS Sensor

      From mountains high to valleys low, your Jeep Grand Cherokee has been everywhere. Keeping its ability to stop at a moment's notice is a necessity. With a quality Jeep Grand Cherokee ABS sensor from AutoZone, your vehicle is able to figure out your speed and help keep you on the road.

      Stopping your vehicle speedily and safely is the main goal of your Grand Cherokee's anti-lock brake system. This system is also focusing on diminishing the skidding of your wheels, and, in modern settings, diminishing the skidding on ice, water or snow-filled roads. If you see an ABS warning light on your dash, this indicates a faulty ABS censor. When you purchase a Grand Cherokee anti-lock brake sensor from AutoZone, feel free to utilize our free battery charging and engine diagnostic testing during your next in-store visit. You can benefit from trustworthy advice from our expert staff to help you find the right product at the right price.

      Customer

      Reviews

      Reviews for


      !!!DO NOT PRY OLD SENSOR OUT!!!

      Robert

      in 9 months

      I was getting left front wheel speed sensor error. Have replaced these sensors before but this last go around was a NIGHTMARE. I removed the tire, caliper and rotor to get to the sensor on my 2005 Grand Cherokee. I needed an Allen wrench to remove the bolt holding the sensor down. Make sure you clean out the Allen hole on the bolt so not to strip IF you have an Allen bolt. Here's where the job can go south REAL FAST; Throughly clean and SOAK the sensor in penetrating oil! DO NOT TRY AND PRY THE SENSOR OUT! If it snaps you will have to drill out the remaining sensor and pick out ALL the pices with long slender tweezers!! After soaking use flat nosed pliers and rotate back and fourth while pulling up Clean bore with a Qtip and lightly coat new sensor with thin coat of Vaseline or dielectric grease. Carefully push sensor straight down with same procedure as removal. Also, apply thin coat of dielectric grease on sensor connector. I use a Qtip and coat the seal surface.

      What kind of vehicle do you drive? 2005 Jeep Grand Cherokee

      I was getting left front wheel speed sensor error. Have replaced these sensors before but this last go around was a NIGHTMARE. I removed the tire, caliper and rotor to get to the sensor on my 2005 Grand Cherokee. I needed an Allen wrench to remove the bolt holding the sensor down. Make sure you clean out the Allen hole on the bolt so not to strip IF you have an Allen bolt. Here's where the job can go south REAL FAST; Throughly clean and SOAK the sensor in penetrating oil! DO NOT TRY AND PRY THE SENSOR OUT! If it snaps you will have to drill out the remaining sensor and pick out ALL the pices with long slender tweezers!! After soaking use flat nosed pliers and rotate back and fourth while pulling up Clean bore with a Qtip and lightly coat new sensor with thin coat of Vaseline or dielectric grease. Carefully push sensor straight down with same procedure as removal. Also, apply thin coat of dielectric grease on sensor connector. I use a Qtip and coat the seal surface.

      What kind of vehicle do you drive? 2005 Jeep Grand Cherokee

      Reviews for


      Plug and play

      Robbie61

      in a year

      Got a trouble code, C1044, after scanning when abs light activated ( it came on after driving a few miles and would go out next time I drove the vehicle, only to activate again after a few miles). After inspecting and cleaning the tone wheel no signs of damage. Because the fault was so intermittent I figured the circuit voltage was correct so I was able to determine that the wheel speed sensor was faulty. I replaced the sensor and it corrected the issue.

      What kind of vehicle do you drive? 2005 Jeep Grand Cherokee

      Got a trouble code, C1044, after scanning when abs light activated ( it came on after driving a few miles and would go out next time I drove the vehicle, only to activate again after a few miles). After inspecting and cleaning the tone wheel no signs of damage. Because the fault was so intermittent I figured the circuit voltage was correct so I was able to determine that the wheel speed sensor was faulty. I replaced the sensor and it corrected the issue.

      What kind of vehicle do you drive? 2005 Jeep Grand Cherokee