How to Select the Right Hitch Ball for Level Towing

The ball mount raises or lowers the hitch ball to ensure that your tow vehicle and trailer remain level as you travel. Correct ball mounts will match shaft size to receiver tube dimensions. The key is to get a ball mount that allows the trailer coupler to be level with the ground.

What is a Ball Mount?

A Ball Mount is a removable hitch ball platform that slides into the receiver of a hitch and fastens with a pin and clip. Different ball mounts can be used to raise or lower the height of the ball to allow for level trailer towing.

Different classes of ball mounts fit different receiver tubes:

  • Class I & II: 1-1/4″ receiver tube
  • Class III & IV: 2″ receiver tube
  • Class V: 2″ or 2-1/2″ receiver tube

It is important to identify mounting location, hitch ball, shank diameter, and thickness if you are not purchasing a combo. Then you can measure the diameter of the hole and thickness of the mounting location to choose a matching ball mount.

What is a Hitch Ball?

A hitch ball (or trailer ball or just ball) is the ball-shaped attachment that connects the trailer to a hitch. While the diameter of the hitch ball is fairly standard, shank diameters, and hitch ball weight ratings may differ. The rating of the hitch ball is just as important as the receiver hitch ratings.

Ball Diameter (A): Check the top of the trailer coupler for the size of the ball diameter required. The size is usually stamped there. Recreational and light commercial hitch balls come in a variety of sizes including 1-7/8″, 2″, 2-5/16″ and occasionaly 3″. In general lighter trailers use smaller hitch balls. It is VERY important to match the trailer to the correct hitch ball.

Shank Diameter (B): This is the diameter of the threaded shaft that is inserted through the ball mount. Shanks come in a variety of sizes (5/8″, 3/4″, 1″, and 1-1/4″) and capacities. (7,000lbs-17,000lbs)

Shank Length (C): This is length of shaft that extends beyond the mounting base of the hitch ball. It is important to use a shank that is long enough to extend beyond the thickness of the draw bar mounting tab to ensure that enough threads are available to securely fasten the ball to the mount.

Shank Rise (D): The height of the shank can be used to raise a trailer back to level in the event the “rise” or “drop” of a ball mount is inadequate.

How to Level Your Trailer

1. Arrange Your Vehicle and Trailer

Park your vehicle and trailer on level ground.

2. Level Out the Trailer Tongue

Place a level on top of the trailer tongue, and adjust the trailer up or down until the bubble inside the level shows that the trailer tongue is level with the ground below.

3. Measure the Draw Bar Shank’s Height

Using a tape measure or something similar, measure from the top of the part of the draw bar that connects with the receiver tube to the ground. Record this measurement and label it A.

4. Measure the Trailer Tongue’s Height

Get your tape measure again and measure from the bottom of the trailer tongue to the ground. Record this measurement and label it B.

5. Subtract for Drop

Subtract B from A for the amount of “drop” you will need to keep your trailer level (AB = “drop”).

If the “drop” value is negative, it is referred to as “rise.”

Advice, how-to guides, and car care information featured on and AutoZone Advice & How-To’s are presented as helpful resources for general maintenance and automotive repairs from a general perspective only and should be used at your own risk. Information is accurate and true to the best of AutoZone’s knowledge, however, there may be omissions, errors or mistakes.

Be sure to consult your owner’s manual, a repair guide, an AutoZoner at a store near you, or a licensed, professional mechanic for vehicle-specific repair information. Refer to the service manual for specific diagnostic, repair and tool information for your particular vehicle. Always chock your wheels prior to lifting a vehicle. Always disconnect the negative battery cable before servicing an electrical application on the vehicle to protect its electrical circuits in the event that a wire is accidentally pierced or grounded. Use caution when working with automotive batteries. Sulfuric acid is caustic and can burn clothing and skin or cause blindness. Always wear gloves and safety glasses and other personal protection equipment, and work in a well-ventilated area. Should electrolyte get on your body or clothing, neutralize it immediately with a solution of baking soda and water. Do not wear ties or loose clothing when working on your vehicle.

FREE Loan-A-Tool® program requires returnable deposit. Please note that the tool that you receive after placing an online order may be in a used but operable condition due to the nature of the Loan-A-Tool® program.

Related Posts