Reviews for Bussmann Fuse Tester and Puller

Got these as spare fuses for my car, and they are just what I needed. No issues. Work perfectly.

We were able to find out that it wasn't the fuse.

Works great. Adjustable. Easy to use. Green light indicator to show fuse is good.

Easy to use

Works as needed

It is a very good tool to check out car fuses. Simple and easy to operate.

works good for price

Check fuse

Worked for testing my car's fuses. Mine are low profile though so I couldn't use the tool to pull them, so something to keep in mind.

Easy and simple to use

Nice easy and fast

Worked great and saved a lot of time

A car to see if I needed a fuse.

Good fuse cheker worked good

I liked this product and it was very easy to use and read.

This was an awesome purchase in no time at all we figured out the bad one and replaced it.

I could not physically pull the fuses from my Wrangler (to search for a power drain) without the advantage of the puller. Pliers will crush these fuses! The tester is a bonus, and the device is small enough to carry, anywhere.

Easy to use with the indicator to detect if fuse is good or bad.

Great

To test my fuses

Fuse checker\r\nWorks great wish I saw this years ago\r\nReplacing fuses would have been easier

Perfect part to get the job done right

Product was purchased for my daughter. She needed something right away. It was in stock and she was able to change the fuse herself.\r\nThank you guys!!

There's not much to say, it's a fuse checker. I initially went in for brake pads that I got someplace else. Everyone was helpful there tho. Prices were decent even tho the brake pads were $8.00 cheaper elsewhere.

This tool worked perfectly.

great inexpensive fuse puller and at the same time has a quick fuse testing light

This a very handy tool for pulling and testing fuses! the puller is especially handy I have some pretty meaty fingers and trying to pull a fuse with them is darn near impossible so this puller is a REALLY good thing to have, and the tester is a quick way to see if the fuse is bad or not.

I needed a fuse puller. In my "best case" scenario I would find one that was more robust. When I saw this one, with the ability to test I didn't think twice! With the ability to adjust the contact points to reach various sizes...I couldn't have asked for anything more!

handy puller and tester. U can't always tell when a fuse is blown, this eliminates the guesswork.

THis one is MUCH better than the one that is available at Oreillys Auto This one is actualy Adjustable. That makes a WORLD IF DIFFERENCE. Thank you AUtozone. You saved me time and money.

This product was great because it served two functions. I was able to test the fuse as well as remove it and that made into job very easy!

It is awesome, not only useful for fuses but also tried it on headlights and it worked!

I brought this couple weeks ago poped it in work just fine

Works great, just what I needed. Easy way to check ur fuses

Pulls fuses, good tester for that purpose

Trying to use on fuses inside the car it was to big had to pull the fuse out and tested some of them

Simple as removing the fuse and testing it for a light. May not actually latch onto all types of fuses to remove though

Works great testing fuse, but not so good pulling flat fuses!!!

I bought a week ago, and it’s pretty awesome/useful

Tester works well. Fuse puller is useless.

Did it’s job

The tester portion works as expected. The fuse puller function however is difficult to use. Due to the way the prongs are shaped, it's difficult to get adequate pressure on them to hold onto a fuse while you pull it. This was with micro2 fuses. It may work better on larger fuses.

It’s hard to use at 1st. But for the most part with some patience it’ll work. It all depends on what your trying to make sure works or not. Make sure your car is on of course, and don’t try to force it on there. It’ll light up with in the right position.

i dislike when i bought it it wasn't working then it started working and told me everything was fine and wasn't

I have joint problems in my fingers making most products hard to use. I had no problems pulling and testing the fuses myself

wasn't precise when trying to get a reading and the pincher was too wide to get a grip on the fuse.

Puller was not small enough to pull out the new relays out. Too big to get into the fuse box in the engine compartment.

Now the prongs got to be smaller than the regular ones so you can see if he have a green light or no light at all the prongs to pull out the fuse doesn't work for this type a fuse pretty much useless

Tester does not spaced properly for certain fuses, gave to use two hands and force to make contact

Didn’t work well